Links

  • galvanized

  • The difference is that hot dip galvanizing is dipped in zinc solution melted by heating, which has fast production speed and thick but uneven coating. The color is dark, the consumption of zinc metal is much, the formation of infiltration layer with the matrix metal, the corrosion resistance is good, and the outdoor environment of hot dip galvanized can be maintained for decades. Cold galvanized is in the plating tank through the current unidirectional zinc gradually plated on the metal surface, the production speed is slow, uniform coating, thin thickness, usually only 3-15 microns, bright appearance, poor corrosion resistance, generally a few months will rust.


  • Post time: 23-02-23
  • blade

  • 2, can quickly let the dog develop home habits, let it learn to wait for the owner to take it out, prevent it from making the home dirty, dirty its nest.
  • 牛栏网

  • Hexagonal

  • 2, galvanized silk mesh forming sheet storage ground should be flat, according to the symbolic needs of regular accumulation, height should not exceed 2M, and away from heat source, avoid exposure.

  • After the optimization of the process, mass production of 0.80mm electro galvanized steel wire electro galvanized zinc layer quality is controlled within 80 ~ 90g/m2, zinc layer quality dispersion is very small; The results show that the average weight of zinc layer is 14.5g/m2, the loss of zinc layer is less than 5%, and the tensile strength of steel wire is 2300 ~ 2500MPa. It not only effectively controls the quality of zinc layer of raw steel wire, but also reduces unnecessary waste and production cost.

  • Hot dip galvanizing is to make the molten metal react with the iron matrix to produce an alloy layer, so that the matrix and the coating are combined. Hot dip galvanizing is to first pickling the iron and steel parts. In order to remove the iron oxide on the surface of the iron and steel parts, after pickling, it is cleaned in the tank of ammonium chloride or zinc chloride aqueous solution or mixed aqueous solution of ammonium chloride and zinc chloride, and then sent into the hot dip plating tank. Hot dip galvanizing has the advantages of uniform coating, strong adhesion and long service life.

  • Core diameter: according to customer requirements (mm)
  • Fence use: generally used as a fence is a plastic-impregnated welded wire mesh with a height of 1.2 meters to 2 meters. Most of the mesh holes are 6cm, and the wire diameter varies from 2mm to 3mm.

  • 4. Packaging: The straightened and cut cold galvanized wire is packaged for transportation and storage.

  • hot

  • Of course, the quality of any product is also affected by the implementation of the manufacturer’s norms. If it is the manufacturer of electric welding mesh in production, it does not have a high implementation of the norms, or the procedural norms on the production line have decreased, or there is no higher requirements on the production link.

  • Post time: 12-08-22
  • hook


  • Post time: 12-10-22
  • The insulation layer of large rolls of galvanized wire and rigid thermal insulation products can be bound with double strands of galvanized iron wire, and the binding interval shall not exceed 400mm. The pipe or corresponding equipment with nominal diameter equal to or greater than 600mm shall stop reinforcement after binding, and the enclosed galvanized steel wire must be winched. The iron or wood rod should be tightened, but the tightening level should be moderate, not too tight or too loose, and not damage the wire. The consumption of wire and steel wire is generally used in drawing process and galvanized disposal.

  • Galvanized hexagonal mesh uses: building wall fixed, heat preservation, heat insulation; Power plant piping, boiler heating; Anti-freezing, residential protection, landscaping protection; Raise chicken and duck, isolate chicken and duck house, play the role of protecting poultry; Protect and support seawalls, hillsides, roads and Bridges and other waterworks.

  • The smaller the mesh of decorative hook mesh, the finer the demand wire, the larger the mesh, the thicker the demand wire. For example, 6.5cm mesh aperture, the required iron diameter is 3.5mm-4mm. Then a fine welding will be broken, and then thick and heavy, workers can not bear.
  • 5. Dry it with a towel.

  • Post time: 07-07-22