Popular articles

Links

  • Unless the stainless steel blade barbed rope produced now is a specially customized model, it is generally produced with a tool length of 22mm, which is what we usually call bto-22 type. It is not necessarily such a specification from 11mm to 65mm there are specifications. Unless the customer insists on customizing the specified length, the barbed rope manufacturer produces the bto-22 stainless steel blade barbed rope.

  • Now the production of stainless steel blade barbed rope unless it is specially customized model, under normal circumstances is the use of 22mm knife length mold production, that is, we usually say BTO-22 type. It is not necessarily such a specification from 11mm to 65mm are specifications. Unless the customer insists on the length of the customized requirements, the barbed rope manufacturers produce is BTO-22 stainless steel blade barbed rope.

  • 1, stress relief before plating where the maximum tensile strength is greater than 1034Mpa key and important parts before plating should be at 200±10℃ stress relief for more than 1 hours, carburizing or surface quenching parts should be at 140±10℃ stress relief for more than 5 hours.


  • Post time: 10-05-23
  • When laying steel wire mesh, according to the laying method from the middle to both sides in turn. Wall plastering engineering use wire mesh material is generally two kinds: one is electroplating, the other is hot dip galvanized. The former has low cost and a wide range of use. The cost of hot-dip galvanized material is slightly higher than that of electroplating, and the cost is high and the life is good to prevent rust. Hot dip galvanizing is in the case of heating plating. After the zinc is melted into liquid form, the base metal is immersed in it so that the zinc interpenetrates with the base metal and binds so tightly that there are no other impurities or defects left in the process.

  • Great attention should be paid to pickling of large rolls of galvanized wire. Acid is highly corrosive. Therefore, when adding acid, the acid must be poured into the water, and it is along the wall of the cylinder, and not thrown down at once, so as not to cause splashing. Remember the order of acid pouring, acid into water rather than water into acid, water into acid will cause splashing and boiling, when pouring acid must wear protective glasses, beside must ensure that there are no non-professional people watching, so as not to cause some acid splashing danger.

  • The welding process of galvanized steel wire mesh because of low carbon steel carbon content is low, manganese and silicon content is low, will not occur severe hardening or quenching structure due to welding. The low carbon steel joints have excellent plasticity and impact toughness after welding. In the welding process, it is generally not necessary to preheat, interlayer temperature control, post-heating control and heat treatment to improve the welding structure.

  • Material: low carbon steel wire
  • Different from double strands of barbed wire to install directly on the ground, the blade thorn rope is fixed on some affiliate products just again, as was the case according to the common on the wall, often wall width is far lower than the diameter of the blade thorn rope under the premise of no such device is fixed in place, use special stents to prevent blade thorn rope can better protect us.

  • (4) granary storage, circle corn net.

  • Galvanized iron wire has tolerance and elasticity, the amount of zinc can reach 300 g/square meter. It has the characteristics of thick galvanized layer and strong corrosion resistance. Widely used in construction, handicrafts, wire mesh, highway guardrail, commodity packaging and ordinary civilian and other fields.

  • Now hexagonal net is used in a large number of Bridges, piers and bridge buttress inclined plane protection, bridge buttress inclined plane there are many kinds, people according to the inclination of the inclined plane to choose the right hexagonal net, when the inclined plane gentle, people generally use gabion slope protection system, and in the case of steep slope, people will use gabion mesh gravity protection wall.

  • Wire rod to stop normalizing or soxaustenitizing treatment, large specifications with spheroidizing annealing instead. In the middle, especially before the waste product drawing process of thermal disposal throughout the selection of soxaustenitizing disposal. Decarbonization should be prevented during thermal disposal. Sulfuric acid or hydrochloric acid pickling was used to remove the oxide sheet after hot treatment. Coating (see lubrication carrier) can be dipped in lime, phosphating, borax disposal or copper plating.
  • Hot dip galvanizing is also called hot dip zinc and hot dip galvanizing: it is an effective way of metal anticorrosion, mainly used in various industries of metal structure facilities. It is to immerse the steel parts after rust removal into zinc solution melted at about 500℃, so that the surface of the steel members is attached with zinc layer, so as to play the purpose of anticorrosion.


  • Post time: 23-12-22
  • The price of galvanized iron wire performance is the key to win, galvanized wire only with good performance, in order to win the market, in order to obtain customer praise. In galvanized wire, the main function of carbon in increasing hardness, less is less easy to rust, the main function of chromium is acid and alkali resistance; Nickel’s main function is high temperature resistance, acid and alkali resistance and conductive use; The main function of iron is magnetic conductivity; The main functions of titanium are low density, high hardness and strong corrosion resistance. The main function of copper is magnetic and electrical conductivity. Different chemical components have different functions, which together form the characteristics of galvanized wire.

  • Three: Packaging: moisture-proof paper, woven bag strip, other packaging can be packed according to customer requirements

  • Some welding methods of galvanized steel mesh will reduce the quality of low carbon steel welded joints, such as electroslag welding. Because the line energy is high, the coarse grains in the heat affected zone of welding will become very coarse, leading to a severe reduction in impact toughness. After welding, it is necessary to normalize with refined grains to improve impact toughness.