• Avoid hanging cages near heaters, as failure to dissipate heat can interfere with bird molting.
  • In general, when exporting and exporting, the blade thorn rope will be packaged and sold, so that the volume occupied in the container is relatively small, which can be easily placed and will not occupy much place.


  • Post time: 16-09-22

  • Post time: 28-10-22
  • Strictly control the pH value of large roll galvanized wire bath, research shows that the size of the bath pH value directly affects the quality of steel wire coating, improper control of pH value will cause loose coating. When the pH value is greater than 3, the steel wire coating has burr caused by fine dendrites, and the surface is not smooth. The current density is strictly controlled. From the microscopic morphology, the higher the current density, the larger the zinc layer grain deposition, the less dense the corresponding zinc layer.


  • Post time: 15-05-23
  • The vertical distance between the lower edge of the Nestor roller cage and the upper edge of the reinforced concrete protective fence is 0.05m. Longitudinal reinforcement adopts hot-dip galvanized netting, double-twist weaving process, barbed wire 2.2mm, main line 2.5mm, netting joint card adopts galvanized steel plate stamping or Q235 carbon steel plate stamping for galvanized.

  • 5, do not pull the wire beyond the plastic limit.
  • 3. When you travel with your dog, it will not cause anxiety to some friends because the dog is scattered in the car, or it will affect safe driving and bring risks.

  • Post time: 15-02-23
  • Because of the pre-tension given to the packaging and binding of galvanized wire, it has the excellent characteristics of low relaxation value, small stress loss, good stability after loading, not easy to deformation, no fracture, strong elasticity, ordinary steel lines and rebar are difficult to compare. The use of advanced galvanized finishing process, therefore, the use of hot-dip galvanized steel wire construction, not only good corrosion resistance, but also beautiful and generous. The product has the characteristics of smooth surface, high dimensional accuracy, good uniformity of zinc layer and strong adhesion.


  • Post time: 12-07-22
  • One is to do a good job of galvanized wire packaging, avoid bumping, to ensure the integrity of the zinc layer;
  • Galvanized silk hook mesh is widely used in warehouses, east and west refrigeration, protective reinforcement, park, zoo fence, Marine fishing fence and construction site fence, machinery and equipment protection. There are two kinds of use, that is, slope protection hook net (slope protection net), coal mine hook net (mine hook net, coal mine support net, roadway support net).


  • Post time: 30-06-22
  • galvanized

  • barbed


  • Post time: 28-09-22
  • Secondly, galvanizing can increase the mechanical strength of the product. The wire drawing process is to draw metal materials to make their grains thinner, thereby improving the mechanical strength of the product. Galvanizing can form a layer of zinc on the surface of the product, and the zinc layer itself has a high hardness, which can provide additional support during the wire drawing process and prevent the metal material from tensile fracture during the wire drawing process. Therefore, galvanized products after wire drawing can increase their strength and stiffness, and improve their tensile strength and torsional resistance.
  •  

  • galvanized


  • Post time: 27-03-23
  • 5. Dry it with a towel.
  • Three is to do a good job in the production site of galvanized wire products clean and tidy, according to the scientific operation method to operate the production, the operator should wear the required dress. If it is hot dip galvanized wire products, we must do a good job of passivation treatment, will be able to effectively prevent discoloration, prolong the method of discoloration, can solve the problem of discoloration.

  • After proper heat treatment or cold drawing hardening, high carbon steel wire has high strength and hardness, high elastic limit and fatigue limit (especially notched fatigue limit), cutting function is acceptable, but welding function and cold plastic deformation ability is poor.

  • The reason why there are black spots in wire mesh welding is that the action of wire feeding should be timely filled in the melting time, and the development should be appropriate. There is no argon gas, long burning, large current, long distance, blunt tungsten needle and high molten pool temperature are the fundamental reasons for blackening. Continuous burning, is about active welding machine energy selection, machine welding will appear black spots.