• 3. Before cleaning the cage, put the birds in a safe place, and then clean out the garbage inside the cage. Clean it up with a sweep. Then use a wet rag to clean on site.
  • In sulfur dioxide, hydrogen sulfide and Marine atmosphere, zinc corrosion resistance is poor, especially in the high temperature and high humidity atmosphere containing organic acid, galvanized wire galvanized layer is easy to be corroded. The surface of galvanized wire galvanized layer uniformity and color of galvanized wire, good quality galvanized wire surface galvanized layer uniformity, zinc adhesion is good, and the color is white, no leakage plating and rust points.

  • The acid activation solution in the production process can remove the corrosion products and oxide film on the surface of the low carbon steel wire without excessive corrosion to the matrix. Galvanized wire can be zincate galvanized or chloride galvanized process, should use appropriate additives to obtain the low carbon steel wire standard requirements of the coating. When galvanized wire after light plating should be light treatment. Control the temperature of the bath of galvanized wire.
  • Cold drawing wire is a metal cold processing, with wire rod as raw material, that is, the mouth of the steel bar. Cold drawing wire is a product produced by a series of processes such as shell stripping, which is a common wire. In the development and production of metal materials, cold drawing wire is a very common material, its performance is good, the range of use is very wide, manufacturers in processing are the use of cold processing to produce.

  • In summary, as a commonly used anticorrosive material, electrogalvanized wire has good corrosion resistance. Its corrosion resistance mainly depends on the thickness, uniformity and structure of zinc layer, substrate material and environmental conditions and other factors. Through reasonable electroplating process and material selection, the corrosion resistance of electrogalvanized wire can be improved and its service life can be extended.

  • 3, the external environment, the climate is dry and ventilated environment is not easy to rust.
  • The quality of hot-dip galvanized barbed wire is only the zinc layer attached to the surface of the wire, and with the chemical reaction, the zinc layer on the surface will gradually lose its role because of the oxidation reaction, which is more prominent in the humid environment. And because the use of rusty wire after all, it is said that the quality of hot-dip galvanized barbed wire is certainly not up to the level of stainless steel barbed wire.

  • The production of large rolls of galvanized wire iron can be divided into two categories, is directly from the iron ore after iron stroke exercise out of the metal, the composition of the ore is iron oxide, silica and other miscellaneous stone.

  • The characteristics of large volume galvanized wire is smooth and bright surface, but wet will affect the brightness of galvanized wire, so we must pay attention to avoid humidity when storing, can support a shelf on the ground, so that galvanized wire and the ground isolation, so that it will not be affected by the surface moisture, there is to pay attention to the change of weather, to avoid galvanized wire rain. Galvanized wire has good toughness and elasticity, the amount of zinc can reach 300 g/square meter. It has the characteristics of thick galvanized layer and strong corrosion resistance.

  • barbed

  • A. When the thickness of the plating is 3-4 mm, the zinc adhesion should be less than 460g/m, that is, the average thickness of the zinc layer is not less than 65 microns.

  • hexagonal

  • The diameter of the wire is generally 0.3mm – 3mm, after the wire is not very strong, need to annealing, annealing this step is very important, can ensure the production of galvanized welding net, with good elasticity and toughness. After welding, the welding mesh becomes black wire welding mesh and can not be put on the market, because its corrosion resistance is poor and the service life is short, so it needs to be galvanized or dipped plastic treatment.

  • Excellent anticorrosive makes its popularity in the feed, the net surface smooth and tidy, increased the look and feel, can be adornment effect, this characteristic makes it to show in the mining industry, due to high quality with low carbon materials as raw materials, to make it unique general iron mesh screen does not have flexibility, determine its plasticity in use process, It can be used for the deep processing manufacturing of hardware technology, the batch swing of complex wall body, underground leakage prevention and cracking prevention, light net body, so that this cost is much lower than the cost of iron screen, more can realize its economy and benefit.

  • The galvanized requirements of the parts to be plated: the surface of the parts to be plated should be smooth, and there is no dirt that cannot be removed by pickling method. Such as paint, grease, cement, asphalt and excessive rotten harmful substances; All welds of welded components shall be sealed without air; Pipe fittings and containers must have exhaust and zinc inlet holes; The workpiece should be finished welded steel pipe without thread, if any thread should be protected.

  • The hot dip galvanized hexagonal net is made of low carbon steel wire by mechanized braided welding and then by hot dip zinc treatment. Net color bright white, thick zinc layer, uniform mesh, mesh surface smooth, solder joint tensile resistance, high corrosion resistance.

  • Most of the production enterprises or large public places, they can play a defense hook mesh in the choice of time, often will hook mesh quality in position, so galvanized hook mesh this product few people are interested in, but does this show that galvanized hook mesh is not useful?


  • Post time: 04-07-22

  • Post time: 01-07-22
  • Electric welding net welding after galvanized is after the completion of the welding and then cold galvanized or hot galvanized; After the first galvanized welding is to change the wire welding mesh, welding can be seen after the completion of the welding spot; The two processes are different prices are also very different, the cost of the first plating after welding is low, the surface is smooth, and the cost of the first welding after plating is higher, not easy to rust.


  • Post time: 24-10-22
  • Hot dip galvanized iron wire using high quality carbon structural steel, after drawing, galvanized iron wire processing. Hot-dip galvanized iron wire is widely used in the manufacture of wire mesh, highway guardrail and construction projects. With thick coating, corrosion resistance, strong coating characteristics. And according to the special needs of users, according to the industry standard to provide various specifications of galvanized wire.

  • Twist flower hexagonal network customized quotation needs to provide the following parameters:

  • With a large pickpocket used for steel wire, into the zinc liquid before the surface of the zinc ash stirring; Use a small outlet for galvanized steel wire; Zinc pot steel wire outlet in 30 minutes, with pickpockets back and forth, until the large, floating zinc residue into brown, real zinc ash, zinc ash surface. The extracted zinc ash should be brown yellow real zinc ash, zinc surface, effectively reduce zinc consumption.

  • The surface coating of galvanized wire can be seen whether the quality of galvanized wire is good or not. If the strength of zinc attached to the wire is very poor, then this galvanized wire do not buy, because this galvanized wire must be poor galvanized wire. High quality galvanized wire in general, the zinc layer attached to the surface of the wire is relatively thick, so when we buy galvanized wire, as long as we look at the thickness of the zinc layer, we can generally judge the quality of galvanized wire.


  • Post time: 13-04-23
  • Poor pretreatment before electroplating; Bath temperature is too low; Poor quality additives or excessive additives and organic impurities can cause poor bonding. The quality of the additive also has an effect on coating foaming. Some additives react incompletely during synthesis and continue to polymerize during long-term storage or use. The additive tends to distort the lattice and create stress, causing the coating to blister.