Popular articles

Latest articles

Links

  • 2, see if solder joint is firm, net width on both sides of whether level off, the wire have broken wire phenomena (note: net length is the length of the wire), welded wire mesh of the solder joint is normal after precise voltage debugging, welding of welded wire mesh with graphite, strong, and the net width on both sides of the cutting time is according to the broken wire knife to ensure smooth on both sides, There will be no leakage cutting on both sides of the protrusion of the wire is not cut off the phenomenon, the wire is broken, because the wire is not used up even if the column hole is blocked by the wire can not enter the normal cause, such as broken phenomenon can appear on the surface of the electric welding network lack of a wire.
  • Compared with hot-dip galvanized barbed rope, it is much better in the circle of mountains and forest protection. Because it can choose several colors on its appearance, different sites have different colors, which is both beautiful and practical, so as to facilitate the growth of natural plants and gradually recover the original ecological environment.

  • For single-layer wound non-rotating wire rope, it is necessary to strictly abide by the above principles, otherwise it is easy to cause permanent deformation of wire rope structure; In the case of multilayer winding, the rotation of the rope is determined by the orientation of the reel’s rope groove to lay the foundation for the next layer. The friction between the wire rope and the extrusion pressure of the multi-layer winding drum are large, and the disorderly rope phenomenon is easy to occur. Therefore, the wire rope with a diameter slightly smaller than the pitch of the rope groove and the diameter of the rope groove should be selected to add the touch area between the wire rope and the drum.

  • hook


  • Post time: 01-06-23
  • The application of electric welding mesh is more widely, at present, it has replaced the use of other parts of the screen, the cost of electric welding mesh is low, the production speed is very fast, so it is very popular. The treatment required before galvanized welding mesh is recrystallization annealing, because the welding mesh must maintain an oxide and no other impurities of pure iron active surface, if you can’t keep its surface clean will lead to poor galvanized effect, galvanized layer and iron material is not tightly combined, so this step is necessary.

  • Galvanized wire to galvanized uniform, a body is now its cross section, the second is the longitudinal uniformity. In the actual operation process, such as the jitter of steel wire, the surface of the pot scum and other reasons will cause galvanized wire surface galvanized layer accumulation, should try to solve the problem.
  • 3. The front and back twist barbed wire has a beautiful appearance
  • Steel wire and iron wire have a lot of similarities, but carefully distinguish, you will find that they are not only different in the material, but also in the product characteristics are very different. So when choosing, make sure you make a clear distinction between the two. Steel wire factory introduces steel wire carbon structure steel made above, generally not galvanized, used for machinery, spring. Black and hard; Iron wire: low carbon steel (mild steel), galvanized, used for joining and wrapping. It’s white and soft.

  • blade

  • The color of powder coating is divided into: blade blue, grass green, dark green, yellow. Spray blade gill net by hot-dip galvanized steel plate or stainless steel sheet stamping out sharp knife sheet, high tension galvanized steel wire or stainless steel wire as the core of the resistance device. Because the barbed wire shape is not easy to contact, so it can reach an excellent barrier effect. The primary raw material of the product is galvanized sheet, stainless steel plate, high quality low carbon steel wire (electric galvanized, hot galvanized, plastic coated, plastic sprayed) wire, blue, green, yellow and other colors.


  • Post time: 23-05-22
  • With a large pickpocket used for steel wire, into the zinc liquid before the surface of the zinc ash stirring; Use a small outlet for galvanized steel wire; Zinc pot steel wire outlet in 30 minutes, with pickpockets back and forth, until the large, floating zinc residue into brown, real zinc ash, zinc ash surface. The extracted zinc ash should be brown yellow real zinc ash, zinc surface, effectively reduce zinc consumption. This is one of the measures to reduce zinc consumption, but it is also a real problem, which has not been solved for many years.

  • 5, the concentration of plating aid can not be too high, which is a factor that can not be ignored to reduce zinc consumption. The concentration of plating aid should not be too high. The galvanized line must be added with ammonium chloride and zinc chloride according to the data of laboratory analysis, and the specific gravity of the composite solution should be controlled within the range of 50~80g/L. If ammonium chloride or zinc chloride is arbitrarily added without the results of laboratory analysis, it should be criticized and educated, and economic treatment should be given if necessary.

  • Hexagonal net weaving methods: positive twist, reverse twist, two-way twisting, first editing after plating, first plating after editing, and then divided into hot dip galvanized hexagonal net, electric galvanized hexagonal net, PVC plastic coated hexagonal net, stainless steel hexagonal net, etc.

  • Characteristics: strong anti-corrosion performance, bright appearance, beautiful appearance.