• welding


  • Post time: 30-06-22
  • Wire diameter: 0.6 (mm)
  • Materials of qualified quality should be kept marked for reference when used. In order to remove the surface film, surface inclusion and other defects on the surface of the large roll galvanized wire on the surface of the sedimentary layer to the local surface, it can be found and treated by conventional technology; Excess foam is caused by soaps and saponable fatty surfactants being brought into the tank. Moderate foam formation rates may be harmless. The presence of small homogeneous particles of large denier in the tank can stabilize the foam layer, but the accumulation of too many solid particles can cause explosion.

  • With the rapid development of market economy, all walks of life are improving the production process and quality of products, galvanized iron wire industry can not be an exception, of course. However, as a result of galvanized iron wire types differ, its characteristics and production process is also different. Galvanized wire selection of high quality low carbon steel rod processing, is the selection of high quality low carbon steel.

  • Non-proportional extension strength: It is mainly for hard steel without yield point. It is defined as the stress where the residual elongation of the standard distance part reaches 0.2% of the length of the original standard distance.
  • The application of electric welding mesh is more widely, at present, it has replaced the use of other parts of the screen, the cost of electric welding mesh is low, the production speed is very fast, so it is very popular. The treatment required before galvanized welding mesh is recrystallization annealing, because the welding mesh must maintain an oxide and no other impurities of pure iron active surface, if you can’t keep its surface clean will lead to poor galvanized effect, galvanized layer and iron material is not tightly combined, so this step is necessary.

  • Galvanized hook mesh standard is thorough, mesh planning: 3cm-20cm, silk planning: 1.2mm-4.5mm, galvanized hook mesh 6000 square meters, some standards are available. Benefits: The selection of low carbon steel wire, surface for cold galvanized (electric galvanized) hot dip galvanized anticorrosion treatment, mesh wire strong, strong protection, long anticorrosion time.

  • The middle of the two thorns is 7 to 8 circles, while the ordinary thorn rope is only 3 and a half circles, showing neat and beautiful.

  • hexagon

  • Galvanized also has several different methods, the so-called hot dip galvanizing is put racing in the zinc bath, need to clean them on metal, which ensures that formed between metal and coating adhesive, after cleaning, the matrix metal is dissolved, to clear any residual oxides of residue and then immerse the substrate metal heating liquid zinc, and metallurgical bonding is formed.
  • wire

  • welding


  • Post time: 09-03-23
  • Thorn rope factory can not only have one type of product when processing thorn rope, a variety of models can meet the protection needs of different customers.

  • Hexagonal twist flower network is divided into heavy hexagonal network and small hexagonal network two categories. Both are made of steel wire braided with various materials, the difference is that the former uses thicker steel wire, and the latter uses finer steel wire braided.

  • Replace the column that corroded or misinterpreted and so on resulting in the loss of effect, place the replacement area together from the beginning, and reinforce the column with unstable pile foundation in time. The second is about the protection of galvanized barbed rope itself, to repair the damaged local, will be severely replaced by rust.

  • Any application environment, users want a better the strength of the welded wire mesh, only need to improve its intensity, will make better the habit of using demand, but to be improved in the strength of this product, also need to have the condition of many sided, just need to see factory in produce what kind of material, the strength of the product also is the material strength, But a manufacturer does not meet the strength requirements in the data, after all, there is no way to make the strength of the product progress, so this is the necessary condition.

  • The drawing process of the waste product has a great influence on the function of the product. The general selection of about 90% of the larger total surface reduction rate (see area reduction rate) and the smaller pass surface reduction rate (about 23%), to ensure the endurance of the product. On the high strength spring steel wire, pulling should be controlled each time the temperature of the steel wire outlet is lower than 150℃, to prevent the steel wire due to strain aging and change the crack, which is the main drawback of steel wire waste.

  • 5, according to the thickness of the wire diameter to adjust zinc dipping time
  • Annealing is to restore the plasticity of wire, improve the tensile strength of wire, hardness, elastic limit, etc., the wire after annealing is called annealing wire. In the production process of annealing wire, it is very important to ensure the quality of the finished wire, make the wire have certain strength and suitable degree of soft and hard. The annealing temperature is between 800 ℃ and 850℃, and the length of furnace tube is lengthened appropriately for enough holding time.

  • The characteristics of hexagonal wire mesh: strong structure, flat surface, with good corrosion resistance, oxidation resistance and so on.


  • Post time: 09-01-23
  • dog

  • The characteristics of hexagonal wire mesh: strong structure, flat surface, with good corrosion resistance, oxidation resistance and so on.

  • Galvanized hexagonal mesh is a kind of galvanized metal wire mesh, the mesh shape is hexagonal.