Popular articles

Latest articles

  • Galvanizing can be done by zincate galvanizing or chloride galvanizing. Appropriate additives should be used to obtain a coating that meets the requirements of this standard. Light treatment should be carried out after light plating. The parts that need to be dehydrogenated for passivation should be passivated after dehydrogenation. Before passivation, 1%H2SO4 or 1% hydrochloric acid should be applied for activation for 5~15s. Passivation shall be treated with colored chromate unless otherwise specified in the design drawings.
  • The parameters to be provided are as follows:

  • Pet

  • barbed

  • 2, hot plating wire plating after processing


  • Post time: 11-04-23
  • Some customers are more concerned about the quality of the problem, so for the service life is more important, thorn rope factory will generally recommend the use of high zinc thorn rope or stainless steel thorn rope.

  • In the rolling process, if the surface of the steel wire is rough, the relative friction coefficient of the steel wire and roll increases, the friction resistance increases, the steel wire elongation decreases, the width increases. In the production of weighted leather material is easy to wide, is because of its rough surface. On the contrary, the surface of the steel wire is smooth, because the friction resistance between the steel wire and the roll is small, it is easy to extend, and the width is small. Domestic steel wire in order to prevent rust, the surface coated with butter, such as butter removal is not clean, easy to slip when rolled flat, also affect its width.
  • Razor

  • In order to remove defects such as surface film layer and surface inclusion of large roll galvanized wire, it can be treated by conventional technology. The presence of small homogeneous particles of large denier in the tank can stabilize the foam layer, but the accumulation of too many solid particles can cause explosion. Activated carbon mat to remove surface active substances, or through filtration to make the foam less stable, these are effective measures; Other measures should also be taken to minimize the intake of surface active substances. The electroplating speed can be significantly reduced by the introduction of organic matter.

  • galvanized

  • Pet cage from the use of material can be divided into plastic, wire, wire square tube, stainless steel four. General small animal cage multi-purpose is plastic and wire material, such as a lot of hamster cage, chinchilla cage are made of plastic or wire, small aquarium is plastic products, and the vast majority of small and medium-sized bird cage are wire products. The characteristics of this kind of small animal cage, is small, light, easy to carry, but also easy to clean care. For small animal cages, the wire diameter of the general iron wire is not very large, the thickness of the plastic is relatively thin, so the use of the time can not be “violent”, or the cage under the “destruction” will occur welding or plastic crack off.


  • Post time: 12-12-22
  • The policy of wire mesh mesh size, wire, square meter steel content, galvanized amount, etc., to consider the corrosion resistance of wire mesh ability and system safety! Wire mesh galvanized is more fierce than wire diameter, galvanized amount is very important, must be hot plating, welding after plating is better than the first plating after welding, as for wire diameter, summed up to consider the site construction and meet the needs of safety.

  • Cold galvanized, generally speaking, do not need heating, galvanized amount is little, this galvanized parts are easy to fall off in wet environment. Hot dip galvanizing, also known as hot dip galvanizing, is to melt the zinc ingot at high temperature, put some auxiliary materials in, and then dip the metal structural parts into the galvanized groove, so that the metal members are attached to a layer of zinc layer. The advantage of hot dip galvanized is that its anticorrosion ability is strong, the adhesion and hardness of galvanized layer is better.

  • As a very important product of the barbed rope factory blade barbed rope can be said to have made a great contribution, but often due to the opaque processing process often do not get the trust of customers.


  • Post time: 31-05-23
  • Because the large volume of galvanized wire alloy elements in iron ore, can make the copper through the material thickening degree of strengthening, hardness, impact force, strength resistance, closing rate, elongation, so alloy iron in the exercise of good iron, is an important supplementary element. The difference between galvanized wire and general iron wire is very big, general iron wire is cheap, and because iron is not very stable, easy to rust in wet places, so the stability is not very good, life is not very long.


  • Post time: 04-11-22
  • According to the galvanized iron wire manufacturer, galvanized iron wire is the selection of excellent low carbon steel, through drawing forming, pickling rust removal, high temperature annealing, hot dip galvanized, cooling and other processes. Galvanized iron wire should pay attention to the following points in the use process:

  • Widely used in practice, iron wire also has certain harm, simple rust and corrosion, so we can generally use galvanized method to prevent product corrosion. Together in addition to this method, metal commonly used treatment methods and phosphating treatment, oxidation treatment, etc. Metal phosphating treatment: iron and steel products to remove oil, rust, into the specific composition of the salt solution soak, you can form a layer of water soluble salt film on the surface of the metal, this process is called phosphating treatment.


  • Post time: 17-03-23
  • hot

  • The common type of barbed rope is double-strand barbed rope, and the models are 2.0*2.0mm, 2.25*2.25mm, 2.7*2.25mm, and all of them are galvanized barbed rope (plastic coated barbed rope is rarely used). The barbed distance (that is, the distance between winding wires) is generally 14 cm. Here’s what these models mean:

  • Post time: 18-04-23
  • Barbed wire manufacturers focus on galvanized barbed wire, hot galvanized barbed wire, blade barbed wire, stainless steel barbed wire, plastic coated barbed wire, reverse screw barbed wire production for ten years.

  • Our country industry chooses the low carbon steel with good quality as raw material, and then produces the quality galvanized iron wire by drawing, galvanizing and other processes. Now the production technology of galvanized iron wire products can be divided into hot plating and electroplating two kinds of methods. No matter which one is chosen, it should be carried out in accordance with the corresponding operating specifications, so as to better ensure the production of good products. For key and important parts with tensile strength greater than 1034mpa before plating, the stress should be released at 200±10℃ for more than 1 hour and 140±10℃ before plating.

  • galvanized

  • Dark green plastic-coated barbed cords are occasionally used on high-speed trains, but they are also used in small quantities.

  • 4. When cleaning the cage, remember not to brush violently, but pay attention to the strength. Otherwise easy to damage the surface of the paint layer.