Popular articles

Latest articles

Links

  • blade

  • Cold galvanizing, also called galvanizing, is the steel wire placed in the plating tank, through the one-way current to make the metal surface slow galvanized, zinc is slow, and the thickness is only one tenth of hot dip galvanizing, zinc layer is thin, so the rust resistance is not good, placed in the outdoor usually a few months will rust, applied in the outdoor generally in the plastic coating.

  • Post time: 27-10-22
  • If using common galvanized barbed wire due to the influence of climate and environment, will accelerate the corrosion rate of barbed wire lower utilization rate, so use stainless steel barbed wire in coastal areas is the best choice, if it is the environment is dirty it is recommended to use stainless steel barbed wire of nickel content in the highest 316 l, so that you can extend the service life, greatly enhance the protective effect.

  • The different spacing of the thorn rope is mainly in order to save costs to consider, because if they are too close, then obviously a little waste of resources, but the installation is too sparse will not work. Usually the bottom spacing is about 10cm, and the top is up to 20cm, this is because the higher the place is more difficult to climb over, usually more than one meter without the help of tools it is difficult for ordinary people to climb over, and the bottom because of the relatively tight can prevent personnel from drilling in the past.

  • 5, after the light plating should be carried out light treatment.
  • With the improvement of living standards and the reduction of family size, keeping pets is becoming a way of life for many people. According to statistics, the number of pet dogs has reached more than 100 million, and the trend is increasing rapidly every year. Beijing alone had more than 900,000 licensed dogs in 2010, according to a survey, and the number of pet cats is also very large.

  • electrogalvanized

  • Blade

  • In order to make the zinc content of steel wire stable in the future, and maintain its uniformity, as far as possible to reduce the zinc content, and effectively reduce zinc consumption to the actual work, the following measures are proposed by the wire factory:

  • Pet

  • Specifications: According to customer demand compressive strength: 122MPa
  • ① The diameter of galvanized iron wire for drawing shall not be less than 4mm, and the diameter of galvanized iron wire for binding shall not be less than 2.6mm.

  • Two is to pay attention to the storage and use of galvanized wire products, according to the actual environmental standards to choose different specifications of galvanized wire products;

  • The temperature of large roll galvanized wire should be controlled at 30 to 50℃ during electroplating. Because the chloride ions in the bath are very corrosive, quartz glass heaters are generally used. Continuous production does not need heating, but needs cooling. Cooling can be in the groove side row thin wall plastic pipe, through the flow of tap water cooling, can also be used as a titanium pipe temperature control device.

  • 2. The cage must be strong
  • Three, the use of different technologies
  • Technical product wire, choose a wire special processing, no broken end, zinc amount uniform bright, general quotation slightly expensive. Galvanized silk also contains sprinkling: one plate per volume weight of about 100kg-1000 kg, mainly suitable for industry, agriculture, animal husbandry. Strong corrosion ability, solid coating and other characteristics.

  • Uses: water conservancy engineering, river regulation engineering, dike engineering, ecological protection engineering, channel lining, road engineering, river bank reinforcement, ocean engineering, landscape design engineering, bridge reinforcement, railway and highway slope protection, retaining wall, ecological river bank slope regulation and other engineering.

  • The prepared black wire welding net is placed in environmental protection galvanized equipment for galvanized treatment. The surface of galvanized welding net is evenly covered with a layer of metal zinc. The corrosion resistance of zinc is very good and it is not easy to be oxidized. The wire diameter error of galvanized welding mesh is very strict, and the gap should be controlled at about 0.02 mm. But whether the tension of an electric welding mesh is qualified, can only be tested by professional tools.


  • Post time: 13-07-22
  • blade

  • Most cattle netting is mechanically woven from highly malleable and corrosion-resistant mild steel wire or PVC coated steel wire. Several commonly used raw materials for the manufacture of cattle net are electrogalvanized wire, hot-dip galvanized wire, Galfan steel wire, ten percent aluminum zinc alloy steel wire and the new type of selenium chromium steel wire.


  • Post time: 31-03-23
  • Galvanized

  • Application

  • Galvanized iron wire has excellent endurance and elasticity, zinc content can reach 300 grams/square meter. It has the characteristics of thick galvanized layer and strong corrosion resistance. Widely used in construction, handicrafts, silk screen preparation, highway guardrail, commodity packaging and ordinary civilian categories.

  • steel


  • Post time: 27-10-22
  • Choose a cage that can stand up straight in order to keep your dog comfortable. Lay down with your feet out wide. The dog, can save much, can buy a small cage, can also see it as the same as people, give it a bigger cage, so that it can use half to activity, half to sleep. Use an old blanket for your dog’s crate, or buy a pet mat, as long as it’s comfortable.

  • The uniformity of galvanized wire is reflected in what aspects:
  • There is as far as possible not to show the trace of the application of wire, wire wound flower stems should be wrapped with green or brown tape, in order to cover the trace of the use of wire, in the use of wire modeling can make the drooping flower head raised, and the flower head reinforcement, for herbs and other flower material soft plants, can make the stalk straight. Wire shearing method: if you want to cut the wire, the wire should be straightened and then cut, can not bend the wire, fold and then cut, otherwise, the wire cut is not straight, will bring a small hook, affect the use.