Current location:d shape weather stripping >>Text

d shape weather stripping

Hebei Qiuzhuo door bottom noise seal64People have read

Introduction...



Links

  • Hot – plated wire average performance: reflected in its cross – section, longitudinal uniformity. In the actual process of operation, such as steel wire jitter, the surface scum plating pot and other reasons will cause the surface of galvanized wire galvanized layer accumulation, should strive to solve the problem. In addition to these reasons, we should pay attention to the tooling and process must be stable, and regular testing should be done to ensure the uniformity of the galvanized layer.

  • The production process of large rolls of galvanized wire is a level of drawing, through the mold into a slightly smaller diameter than the original. And so on down to the desired length. One pull is not desirable, must be numbered, from coarse to fine is dependent on metal ductility. If it changes too much it just breaks. After drawing to a certain diameter, galvanized, so that the finished product.

  • galvanized

  • All can do spring can be called spring steel wire, and high carbon is the highest carbon content. Features: WITH high strength and hardness, high elastic limit and fatigue limit (especially notched fatigue limit), cutting function is OK, but welding function and cold plastic deformation ability is poor.

  • 4: spray blade barbed rope long service life.
  • The external environment has great influence on the preservation of galvanized wire mesh. In the rainy season, it is necessary to pay attention to the air humidity of the workshop, warehouse and other departments. It is recommended to use a humidifier. Usually, the moisture absorption of book paper is larger than that of powder paper, and the pH value is higher. Generally speaking, in the normal environment of storage wire, storage time of two years is not corroded wire phenomenon. However, it should be noted that in the process of handling the iron wire, it should be handled gently to avoid the position of the coiling coil, which will cause the smooth pulling of the wire and affect the production.

  • Non-proportional extension strength: It is mainly for hard steel without yield point. It is defined as the stress where the residual elongation of the standard distance part reaches 0.2% of the length of the original standard distance.
  • But there are some necessary precautions in the production of galvanized wire. Remove all tools and piles on the work site and equipment that hinder activities, and slowly put the wire into the cylinder during pickling to prevent acid splashing on the body. When adding acid, the acid must be slowly poured into the water. Do not pour water into the acid to prevent acid spillage and injury. Workers should wear protective glasses when working. Then in the handling of wire and other items, it is strictly prohibited to push hard.

  • The acceptance of cold-drawn low carbon steel wire shall be conducted according to the same production unit, the same raw material, the same diameter, and shall not exceed 30T for an inspection lot, and check the base material into the factory or out of the inspection statement. The inspection items for each inspection lot are appearance quality, diameter error, tensile test (including tensile strength and elongation) and repeated bending test.
  • 2.7*2.25mm means that the two strands are 2.7mm silk, and the thorns are 2.25mm silk.
  • Product features: strong structure, flat surface, with good corrosion resistance, oxidation resistance. The material of small hexagonal mesh is the same as that of other hexagonal mesh, which is generally made of low carbon steel wire, stainless steel wire and galvanized steel wire as raw materials by the hexagonal mesh machine.

  • barbed


  • Post time: 11-04-23
  • The difference is that hot dip galvanizing is dipped in zinc solution melted by heating, which has fast production speed and thick but uneven coating. The color is dark, the consumption of zinc metal is much, the formation of infiltration layer with the matrix metal, the corrosion resistance is good, and the outdoor environment of hot dip galvanized can be maintained for decades. Cold galvanized is in the plating tank through the current unidirectional zinc gradually plated on the metal surface, the production speed is slow, uniform coating, thin thickness, usually only 3-15 microns, bright appearance, poor corrosion resistance, generally a few months will rust.

  • Pet


  • Post time: 22-06-22
  • Hexagonal cage has a wide range of applications, with the progress of science and technology, has been extended to the major hydraulic, civil engineering. Geotechnical engineering and other projects. In hydraulic hexagonal cage in river construction from closed utility, think appropriate and the use of hexagonal cage to fill stone, fixed river, can be used to avoid river erosion brought water and soil loss. In civil engineering projects, hexagonal cage that is suitable and the use of similar particle size volume particles to fill, mesh wall is formed between the cage, which is the stone cage retaining wall.

  • galvanized

  • (5) We can surfacing the parts with wear and other failures, so as to obtain the surface surfacing layer with deep penetration, smooth surface and excellent performance.
  • blade


  • Post time: 27-03-23
  • Welded wire mesh can be made into mesh form, the net surface jinsu or coating process, can be used in welded wire mesh and surface to form a layer of protective film, can effectively make the wire with the outside world with water or corrosive substances isolation, can achieve the effect of growth time, also can make the mesh surface present a different color, make the mesh to achieve the effect of beautiful. After the dip plastic mesh is usually used for outdoor, and column links, can play a protective effect against theft.

  • Stainless steel blade barbed rope production process is basically similar to galvanized blade barbed rope production process, usually according to the mold to determine the size of the blade.

  • Impregnated

  • The different spacing of the thorn rope is mainly in order to save costs to consider, because if they are too close, then obviously a little waste of resources, but the installation is too sparse will not work. Usually the bottom spacing is about 10cm, and the top is up to 20cm, this is because the higher the place is more difficult to climb over, usually more than one meter without the help of tools it is difficult for ordinary people to climb over, and the bottom because of the relatively tight can prevent personnel from drilling in the past.