Current location:indoor non slip mats >>Text

indoor non slip mats

Hebei Qiuzhuo door bottom noise seal77People have read

Introduction...



Latest articles

  • galvanized

  • Hexagonal net weaving methods: positive twist, reverse twist, two-way twisting, first editing after plating, first plating after editing, and then divided into hot dip galvanized hexagonal net, electric galvanized hexagonal net, PVC plastic coated hexagonal net, stainless steel hexagonal net, etc.


  • Post time: 12-04-23
  • With other coatings, the opposite is true. Rust builds up immediately and spreads quickly underneath the coating, causing it to peel. The depletion of zinc in the atmosphere is very slow, about 1/17 to 1/18 of the corrosion rate of steel, and is predictable. Its life span far exceeds that of any other coating. The life of the coating depends on the thickness of the coating in a particular environment. And the coating thickness is determined by the thickness of the steel, that is, the thicker the steel is easy to get thicker coating, so the thick steel part of the same steel structure must also get thicker coating, in order to ensure a longer life.

  • Compared with other galvanizing processes, galvanized steel wire has low cleaning requirements before plating. However, under the current trend of increasing the quality level of galvanized layer, some pollutants brought into the plating tank are obviously harmful. Because cleaning galvanized coating wastes a lot of time and reduces production, it is very important to properly clean and effectively rinse the substrate before electroplating.

  • The difference is that hot dip galvanizing is dipped in zinc solution melted by heating, which has fast production speed and thick but uneven coating. The color is dark, the consumption of zinc metal is much, the formation of infiltration layer with the matrix metal, the corrosion resistance is good, and the outdoor environment of hot dip galvanized can be maintained for decades. Cold galvanized is in the plating tank through the current unidirectional zinc gradually plated on the metal surface, the production speed is slow, uniform coating, thin thickness, usually only 3-15 microns, bright appearance, poor corrosion resistance, generally a few months will rust.

  • As we all know, iron wire rust is due to contact with water and oxygen chemical reaction, therefore, how to prevent galvanized iron wire rust, first of all, in the storage of galvanized iron wire should choose ventilated dry place, avoid wet or rain leakage, in use, in addition to follow the principle of first in first out, if accidentally caused by the destruction of galvanized layer, should be coated with anti-rust paint treatment, Otherwise, it is easy to lose the protection of galvanized layer and cause galvanized iron wire rust.

  • hook

  • Tolerance range: radial mesh deviation range is not more than ± 4%, zonal mesh deviation range is not more than ± 3%; Solder joint tensile strength exceeds the national standard.

  • Post time: 17-06-22
  • Galvanized wire coating is galvanized, aluminum plated, coated with nylon or plastic, etc. Zinc is divided into thin coating of steel wire after plating and thick coating of galvanized steel wire after drawing. The mechanical properties of thick coating are reduced compared with smooth steel wire rope, which should be used in severe corrosion environment. It is more resistant to corrosion, wear and heat than galvanized wire rope, using the first plating and then drawing method of production. Coated nylon or plastic wire rope is divided into two kinds of coated rope and coated stock after the rope.

  • Three is to do a good job of galvanized silk product production site clean and tidy, in accordance with the scientific method of operation to operate the production, the operator should wear the required dress. If it is hot dip galvanized wire products, we must do a good job of passivation treatment, will be able to effectively prevent discoloration, prolong the method of discoloration, can solve the problem of discoloration.

  • Bridge protection system generally do not need to be specially installed special drainage system, the use of hexagonal mesh made of gabion mesh box, the inside of the filler are selected stones, these stones are not easy to wear, and between the stones and stones will retain some gaps, so it is very good to meet the drainage requirements.

  • Steel wire and iron wire have a lot of similarities, but carefully distinguish, you will find that they are not only different in the material, but also in the product characteristics are very different. So when choosing, make sure you make a clear distinction between the two. Steel wire factory introduces steel wire carbon structure steel made above, generally not galvanized, used for machinery, spring. Black and hard; Iron wire: low carbon steel (mild steel), galvanized, used for joining and wrapping. It’s white and soft.


  • Post time: 12-05-23

  • Post time: 11-01-23

  • Post time: 19-08-22

  • Post time: 25-05-22
  • Product features: hot dip galvanized electric welding mesh surface flat, uniform mesh, straight warp and weft wire, diagonal accuracy within 3-5 mm. The structure of the net surface is strong, strong integrity, with strong corrosion resistance, beautiful, wide use and other characteristics.


  • Post time: 07-05-22
  • High quality galvanized wire in general, the zinc layer attached to the surface of the wire is relatively thick, so when we buy galvanized wire, as long as we look at the thickness of the zinc layer machine, we can generally judge whether the quality of galvanized wire is high quality.


  • Post time: 13-06-22
  • 4. Keep the rinse water clean after pickling the steel wire

  • 6, barbed rope protection network layout should be according to the road boundary terrain necessary renovation, flat section level set, slope section slope or step set.

  • thorn

  • Annealing wire is widely used mainly because it has a good elasticity and flexibility, in the annealing process can be a good control of its hardness and softness, it is mainly made of iron wire, more commonly used in the construction industry tie wire use. So why annealing wire according to material properties processing?